300MW锅炉低NOx燃烧系统改造效果分析

针对日益严重的环境污染、锅炉热效率低等问题，阐述了燃煤锅炉炉内空间分级燃烧技术、煤粉浓淡高效分离技术改造项目和特点，提出了对燃烧器系统、一次风管道、二次风系统和空预器系统等系统进行具体的低氮改造措施。分析了300 MW燃煤锅炉低氮改造后的热经济性和安全性。经试验验证，1号锅炉低氮改造后，锅炉NOx 排放量大幅减少，排放浓度降到了280 mg／m3。     

大肠杆菌吸附-化学还原法用废含金催化剂制备金纳米线

采用大肠杆菌吸附-化学还原法,以大肠杆菌(ECCs)为模板、十六烷基三甲基溴化铵为保护剂、抗坏血酸为还原剂,由废含金催化剂制备金纳米线(AuNWs)。采用XRD,SEM,TEM等技术对AuNWs进行表征。研究了AuNWs对罗丹明6G(R6G)和4-巯基苯甲酸(4-MBA)的拉曼散射信号的增强效果。实验结果表明:在制备过程中加入微生物ECCs,可使金回收率提高约20百分点;当溶液pH小于4时,反应2 h后,有大量呈线状的AuNWs聚集沉降,金回收率可达99%1以上。表征结果显示,AuNWs呈多晶结构,晶格间距为0.23 nm。表面增强拉曼散射分析表明,AuNWs对R6G和4-MBA具有良好的拉曼光谱增强性能。     

Ti3C2纳米层状材料对废水中Cr（Ⅵ）的光催化去除性能

以Ti₃AlC₂为原料,采用HF刻蚀工艺制备出12种Ti₃C₂纳米层状材料,对其形貌进行了表征,并考察了以其作为光催化剂对废水中Cr（Ⅵ）的处理效果。实验结果表明：HF体积分数为80%、刻蚀时间为48 h时得到的MX-80-48的形貌较好;MX-80-48具有类似石墨烯的二维层状结构,纳米层厚度约20~50 nm,孔径2~10 nm,比表面积14.8 m²/g,在400~700 nm可见光范围内表现出强烈的吸光性;当Cr（Ⅵ）的初始质量浓度为40.00 mg/L、MX-80-48投加量为200 mg/L、pH=2、反应时间4 h（暗反应1 h+光照3 h）时,Cr（Ⅵ）去除率可达100%。     

Enhanced sludge solubilization by microbubble ozonation

A microbubble ozonation process for enhancing sludge solubilization was proposed and its performance was evaluated in comparison to a conventional ozone bubble contactor. Microbubbles are defined as bubbles with diameters less than several tens of micrometers. Previous studies have demonstrated that microbubbles could accelerate the formation of hydroxyl radicals and hence improve the ozonation of dyestuff wastewater. The results of this study showed that microbubble ozonation was effective in increasing ozone utilization and improving sludge solubilization. For a contact time of 80 min, an ozone utilization efficiency of more than 99% was obtained using the microbubble system, while it gradually decreased from 94% to 72% for the bubble contactor. The rate of microbial inactivation was obviously faster in the microbubble system. At an ozone dose of 0.02 g O₃ g⁻¹ TSS, about 80% of microorganisms were inactivated in the microbubble system, compared with about 50% inactivation for the bubble contactor. Compared to the bubble contactor, more than two times of COD and total nitrogen, and eight times of total phosphorus content were released from the sludge into the supernatant by using the microbubble system at the same ozone dosage. The application of microbubble technology in ozonation processes may provide an effective and low cost approach for sludge reduction.     

Pre-concentration and separation of heavy metal ions by chemically modified waste paper gel

Iminodiacetic acid was immobilized on waste paper by chemical modification in order to develop a new type of adsorption gel for heavy metal ions. Adsorption behavior of the gel was investigated for a number of metal ions, specifically Cu(II), Pb(II), Fe(III), Ni(II), Cd(II), and Co(II) at acidic pH. From batch adsorption tests, the order of selectivity was found to be as follows: Cu(II)  Fe(III) > Pb(II) > Ni(II)  Co(II) > Cd(II). Column tests were carried out for pairs of metal ions to understand the separation and pre-concentration behavior of the gel. It was found that mutual separation of Ni(II) from Co(II) and that of Pb(II) from Cd(II) can be achieved at pH 3. Similarly, selective separation of Cu(II) from Cu(II)–Fe(III) and Cu(II)–Pb(II) mixtures at pH 1.5 and 2, respectively, was observed by using this new adsorption gel. In all cases, almost complete recovery of the adsorbed metal was confirmed by elution tests with HCl.     

Spatial cost efficiency in waste paper handling: the case of corrugated board in Sweden

This paper analyzes the spatial cost efficiency of the Swedish legislation regarding waste disposal handling. We focus on the case of corrugated board and recognize that the different counties in Sweden possess different economic prerequisites in terms of waste paper recovery and utilization potential. We employ data for six corrugated board mills and 20 counties and a non-linear programming model to identify the least cost strategy for reaching the politically specified recycling target of a 65% recovery rate for corrugated board. That is, the total costs of recovering a minimum of 65% in each county are calculated and compared with the case when the country as a whole recovers 65% of all old corrugated board is collected but there exist no uniform target for each county. The conclusion is that from an efficiency point of view the recovery efforts should be concentrated to the highly populated and urbanized counties, and not be uniformly divided throughout the country. In the base case, the results suggest that the cost efficient county-specific recovery rates should range from 51 to 72%.     

潮土细菌及真菌群落对化肥减量配施有机肥和秸秆的响应

为了研究化肥减量配施有机肥和秸秆对华北麦玉轮作田潮土细菌和真菌群落的影响,在天津市宁河区试验基地开展田间定位施肥试验,采用Illumina高通量测序技术比较了5种施肥模式（单施化肥处理,F;化肥减施处理,FR;化肥减量与秸秆配施处理,FRS;化肥减量与有机肥配施处理,FRO;化肥减量与有机肥和秸秆配施处理,FROS）下土壤细菌及真菌群落的组成、多样性和结构差异,并结合土壤理化性质分析,探究不同施肥处理下驱动细菌和真菌群落变化的关键土壤环境因子.结果表明,FRO处理显著提高了土壤SOM含量.FROS处理的TP含量显著高于FRS处理,增加了13.33%.FRO和FROS处理AP含量较其它处理显著增加,NH₄⁺-N含量显著高于化肥处理（F和FR）.各施肥处理土壤中优势细菌门类均为变形菌门（Proteobacteria）、放线菌门（Actinobacteria）、绿弯菌门（Chloroflexi）和酸杆菌门（Acidobacteria）,优势真菌门类均为子囊菌门（Ascomycota）.在化肥减量配施有机肥（FRO）的基础上添加秸秆（FROS）显著降低了放线菌门（Actinobacteria）的相对丰度.FRS和FROS处理均显著降低了芽单胞菌门（Gemmatimonadetes）的相对丰度.FROS处理显著提高了浮霉菌门（Planctomycetes）和疣微菌门（Verrucomicrobia）的相对丰度.对于真菌群落而言,有机肥（FRO和FROS）的施入显著提高了子囊菌门（Ascomycota）的相对丰度.与FR处理相比,FROS处理显著降低了被孢菌门（Mortierellomycota）和油壶菌门（Olpidiomycota）的相对丰度,且FRS处理同样显著降低了油壶菌门（Olpidiomycota）的相对丰度.FROS处理的细菌群落Shannon多样性指数显著高于F和FR处理,分别增加了1.26%和1.25%,Chao1指数较F处理显著增加了4.51%,细菌Shannon多样性指数与AP和NH₄⁺-N含量显著正相关（P<0.05）.与FR处理相比,FRS、FRO和FROS处理显著降低了真菌群落Shannon多样性指数,分别达到29.85%、24.94%和25.73%,真菌Shannon多样性指数与AP含量显著负相关（P<0.05）.细菌群落结构在FROS处理下显著区别于F、FR和FRO处理,土壤SM、TP、pH和AP是导致细菌群落结构变化的主要驱动因子;真菌群落结构在FRO和FROS处理下显著区别于F和FR处理,真菌群落结构变化主要受土壤TN、AP和TP的驱动.综上所述,添加有机肥和秸秆改变了土壤理化性质,进而改变了土壤细菌和真菌群落组成,土壤真菌对有机物料的敏感程度高于细菌,细菌和真菌群落结构均受到土壤P的调控,在潮土农业耕作中应引起充分重视.     

中国集成电路制造行业VOCs排放特征及控制对策

中国电子信息产业发展迅速,集成电路等电子器件产量不断增加.在集成电路制造的过程中,大量有机溶剂的使用导致VOCs的产生和排放,从而对大气环境造成影响.为掌握集成电路制造行业VOCs的排放特征,系统分析了其工艺流程和产排污环节,分析了行业废气收集和治理现状,通过对典型企业VOCs的排放监测,获得VOCs排放水平;采用排放因子法核算行业VOCs历史排放量,并基于行业排放特征及减排潜力分析,提出了相应的污染防治对策.结果表明：在集成电路制造中,VOCs排放环节主要集中在光刻、清洗、去胶等过程,1 m²集成电路产量约使用87 g有机溶剂,VOCs产生量较大;通过采取高效的VOCs治理技术,集成电路制造行业有组织排放水平较低,平均浓度为2.1 mg·m^-3,但厂界无组织排放浓度相对较高,平均浓度为0.78 mg·m^-3,接近国家标准的排放限值.根据排放量核算结果,2011—2016年中国集成电路制造行业VOCs排放量呈逐年上升的趋势,主要受产量增加而相应污染控制技术水平提升有限的影响,无组织排放量比重大,占排放总量的38.1%~45.1%.     

金属改性对SAPO-34低温还原NO性能的影响

采用浸渍法制备金属改性SAPO-34分子筛催化剂,分析比较了不同单金属（Cu或Co）及不同比例双金属（Cu：Co=1：1、3：1、5：1,质量比）改性催化剂对NO的催化还原性能,评价了不同催化剂的N₂选择性,并采用扫描电子显微镜（SEM）、比表面积测试、X射线衍射分析（XRD）、NH₃-程序升温脱附（NH₃-TPD）等表征手段对催化剂的物化性能进行了分析.结果表明,单金属Cu改性催化剂具有较宽的温度区间,在250~450℃范围内NO的转化率始终保持在100%;双金属改性使NO转化率保持为100%的最低温度下降了25~50℃,显著拓宽了低温段窗口,其中,Cu₃Co₁/SAPO-34催化剂的低温催化还原性能最好,200℃即可实现100%的NO转化率,175℃下的转化率也高达80%以上.Cu-Co双金属改性SAPO-34分子筛催化剂具有优异的低温催化还原NO性能,具有在机动车尾气、工业废气的低温脱硝治理领域应用的潜力.     

稻田NO3-还原耦合As(III)氧化过程及微生物群落特征

以华南稻田土壤为研究对象通过构建微宇宙体系,研究了淹水稻田自养硝酸盐还原耦合As（III）氧化过程及其微生物群落结构组成.结果表明,NO₃^-的添加促进了稻田土壤中As（III）的氧化,在未添加NO₃^-的处理（Soil+As（III））以及灭菌处理（Sterilized soil+As（III）+NO₃^-）中As（III）未发生明显的氧化;在Soil+As（III）+NO₃^-处理中,NO₃^-有少量被还原,而在Soil+NO₃^-处理中,NO₃^-没有被还原.通过16S rRNA高通量分析在NO₃^-还原耦合As（III）氧化体系中微生物群落结构特征,在Soil+As（III）+NO₃^-处理中shannon指数相对较低为8.19,土壤微生物群落多样性降低,其中在门水平上主要优势菌群为变形菌门Proteobacteria（33%）、绿弯菌门Chloroflexi（11%）、浮霉菌门Planctomycetes（12%）;在属水平上主要的优势菌属为Gemmatimonas（7.4%）以及少量的Singulisphaera、Thermomonas、Bacillus.NO₃^-的添加能够促进稻田土壤中自养As（III）氧化,并且影响着稻田土壤中微生物群落组成.